Maliy pr. V. O., 62/2, liter A, St. Petersburg, Russian Federation, 199178

Hammer crusher HC 5x5

INDUSTRIES

 Mining

 Metallurgical

 Construction

 Chemical

 APPLICATIONS

Coal, foil, polyester resin, glass, slag, salt, automotive catalyst, mica, electrical circuits, food products.

    
    

CHARACTERISTICS

TECHNOLOGICAL PARAMETERS

Average product particle size when 0,8 mm grate is used, mm 0,6-1,5
Comminuted product particle size when 0,8 mm grate is used, mm 90%<2,0
Maximum initial material grain size, mm* 100
Mohs hardness of crushed material, up to 5
Output, kg/hour* 200-7000
TECHNICAL PARAMETRS
Hopper loading door dimensions, mm 220х495
Crusher loading door dimensions, mm 300х498
Size of discharge grate openings, mm 2-50
50 Hz supply voltage, V 380
Electric motor power, kW 22
Rotor speed, rpm 1500
Overall dimensions (Length x Width x Height), mm 1755х840х1185

Weight/weight with control panel, kg

750/755

Hammers material – tool steel

66Mn4

Hammers hardness, HRC

38-42

Compatible control panel

MCP3-10

* Depends on the physical properties of the material and the size of discharge grate openings

ADVANTAGES

MILLING EFFICIENCY

Particles of the material are destroyed by the hammers impacts and friction on the inner surfaces of the crushing chamber, as well as self-grinding.

PRODUCT PARTICLE SIZE AJUSTMENT

There are 3 ways to adjust the particle size of the product:

  • installation of grates with various openings;
  • installation of various sets of hammers;
  • connection of the dust collector.

EASY MAINTENANCE

Hinged covers provide quick access to the milling chamber for inspection and replacement of hammers and grates, and cleaning of the chamber.

OPERATIONAL SAFETY

The end switch excludes start-up with open milling chamber. The size and configuration of the loading hopper preclude access to the milling chamber. All rotating parts and assemblies are covered by the casing.

ABILITY TO COMPETE WITH VARIOUS HAMMERS

HC 5x5 Hammer crusher can be equipped with several types of hammers:

  • 3 types of thickness — 6 mm, 8 mm, and 10 mm;
  • 2 types of sharpening — flat, with symmetrical sharpening.

COMPATIBLE WITH DUST СOLLECTOR

 Ability to connect to dust collector to:

  • increase the output;
  • lower the temperature in the milling chamber;
  • lower the content of dust fraction in the product;
  • separate the material into three fractions: precipitated in the receiving container, cyclone and bag filter.

FREE SUSPENSION OF THE HAMMERS

Free suspension of the hammers on the rotor axes increases their resource and reduces the risk of mill damage due to the indestructible object entering the milling chamber.

QUALITY SPARE PARTS

The hammers are made of tool steel AISI 1066 and can be turned 180°. Self-aligning rotor bearings reduce the load on parts and assemblies. The grate is made of a standard perforated sheet or 5 mm AISI 1066 sheet laser cut openings.

DESCRIPTION OF THE DEVICE

The principle of operation of the hammer crusher is based on the impact on particles of material.

The structure of HC 5x5 Hammer crusher includes: loading hopper, 2 hinged covers, base, rotor, frame and electric motor.

The milling chamber is formed by the inner surface of the hinged covers, part of the base and the discharge grate installed in the base. A rotor (a shaft with 3 discs) is mounted inside the milling chamber. Six axes with hinged hammers are inserted into the holes made on the periphery of the disks.

A loading hopper is installed on one of 2 hinged covers. Inside the hopper there is a curtain. Torque from the electric motor is transmitted through a belt drive to the rotor.

OPERATING PRINCIPLE

The initial material is fed through the loading hopper into the milling chamber, where it is destroyed by hammers, impacts and friction on the inner surfaces of the milling chamber, and is also self-grinding. The milled material passes through the openings of the discharge grate, the size of which determines the size of the product particles, and enters the receiving container.

The hammers are thin rectangular steel plates. The sides of the hammers can be either flat or sharpened at different angles. The number and shape of hammers is determined by the assigned technological task.

PRODUCTION OPTIONS

  • Complete with dust collector.
  • Various hammer sets:

    • 72 flat 10 mm thick hammers;
    • 72 sharpened 10 mm thick hammers;
    • 96 flat 8 mm thick hammers;
    • 96 sharpened 8 mm thick hammers;
    • 96 flat 10 mm thick hammers;
    • 96 sharpened 10 mm thick hammers.

Hinged covers

V-belt drive adjusting device and drive pulley

End switch

MCP control panel

Loading scoops, V=1,2 L

HC 5x5 hammer crusher with dust collector